Simulation Performance Analysis of Shell and Tube Heat Exchanger Using Comsol Multiphysics 5.6 Software
Abstract
A heat exchanger is a very important tool in the fields of engineering and industry, especially in energy conversion. This study was aimed at determining the effects of hot and cold fluid flow velocity on the overall heat transfer coefficient (UA) and effectiveness in shell and tube heat exchangers using COMSOL Multiphysics 5.6 software. Another research objective was to observe the phenomena of heat transfer in the shell and tube type heat exchanger at each hot and cold fluid flow velocity. The heat exchanger was designed with a total length of 800 mm and equipped with 18 tubes having a diameter of 2 in and a length of 600 mm. The material used for tube and shell construction was stainless steel. A simulation was carried out using COMSOL Multiphysics 5.6 software to determine the performance of the designed heat exchanger. The results of this simulation indicated that the effects of hot and cold fluid velocity were directly proportional to the value of UA. The heat exchanger have result the smallest UA value of 80.062 W/m2.K, meanwhile the highest UA value of 174.950 W/m2.K. The heat exchanger have result the minimum effectiveness value of 22.305% and the maximum effectiveness value of 52,047%. The second result is phenomenon stating that the surface temperature of the shell and tube would change along with the increasing velocity of both hot and cold fluids, signifying the heat transfer such as conduction and convection from the fluid to the shell or tube.
Full Text:
PDFReferences
R. Mukherjee, “s Figure 1. TEMA designations for shell-and-tube heat exchangers,” no. February, 2015.
J. Saari, “Faculty of Technology LUT Energy HEAT EXCHANGER,” pp. 1–101, 2011.
M. H. Mousa, N. Miljkovic, and K. Nawaz, “Review of heat transfer enhancement techniques for single phase flows,” Renew. Sustain. Energy Rev., vol. 137, 2021.
A. Dewan, P. Mahanta, K. S. Raju, and K. P. Suresh, “Review of Passive Heat Transfer Augmentation Techniques,” Proc. Inst. Mech. Eng. Part A J. Power Energy, vol. 218, no. 7, pp. 509–527, 2004.
K. Thulukkanam, “Heat Exchanger Design Handbook, Second Edition - Kuppan Thulukkanam,” p. 1260, 2013.
E. Ningsih, A. H. Fahmi, M. Riyanando, M. R. Faiz, E. C. Muliawati, and R. Izroiel, “Desain Shell and Tube Heat Exchanger (STHE) Tipe Counter Current dengan Material Stainless Steel”, Journal of Industrial Process and Chemical Engineering, Vol.2 (2), pp. 124-130, 2022.
S. S. Yogesh, A. S. Selvaraj, D. K. Ravi, and T. K. R. Rajagopal, “Heat transfer and pressure drop characteristics of inclined elliptical fin tube heat exchanger of varying ellipticity ratio using CFD code,” Int. J. Heat Mass Transf., vol. 119, pp. 26–39, 2018.
M. Farnam, M. Khoshvaght-Aliabadi, and M. J. Asadollahzadeh, “Heat transfer intensification of agitated U-tube heat exchanger using twisted-tube and twisted-tape as passive techniques,” Chem. Eng. Process. - Process Intensif., vol. 133, pp. 137–147, 2018.
M. M. Aslam Bhutta, N. Hayat, M. H. Bashir, A. R. Khan, K. N. Ahmad, and S. Khan, “CFD applications in various heat exchangers design: A review,” Appl. Therm. Eng., vol. 32, no. 1, pp. 1–12, 2012.
Safiullah, A. Ahmed, A. Khuhro, I. Tunio, and K. Nishida, “Non-Vaporizing and Vaporizing Diesel Spray Evaluation with Experimental and Computational Approaches,” Quaid-e-Awam Univ. Res. J. Eng. Sci. Technol., vol. 19, no. 2, pp. 114–124, 2021.
E. Ningsih, Fitriana, and D. Pratiwi, “Desain Alat Penukar Panas Tipe Shell and Tube dengan Material Stainless Steel,” pp. 81–89, 2022.
S. Jun and V. M. Puri, “3D milk-fouling model of plate heat exchangers using computational fluid dynamics,” Int. J. Dairy Technol., vol. 58, no. 4, pp. 214–224, 2005.
E. Ningsih, I. Albanna, A. P. Witari, and G. L. Anggraini, “Performance Simulation on the Shell and Tube of Heat Exchanger By Aspen Hysys V.10,” J. Rekayasa Mesin, vol. 13, no. 3, pp. 701–706, 2022.
M. Ravikumar, R. K. Beemaraj, K. M. Arunraja, P. Pandiarajan, and R. Sundaresan, “Heat transfer analysis in fin and tube exchanger using CFD,” Mater. Today Proc., vol. 52, pp. 1603–1605, 2022.
S. Freund and S. Kabelac, “Investigation of local heat transfer coefficients in plate heat exchangers with temperature oscillation IR thermography and CFD,” Int. J. Heat Mass Transf., vol. 53, no. 19–20, pp. 3764–3781, 2010.
T. Ihli, R. Kruessmann, I. Ovchinnikov, P. Norajitra, V. Kuznetsov, and R. Giniyatulin, “An advanced He-cooled divertor concept: Design, cooling technology, and thermohydraulic analyses with CFD,” Fusion Eng. Des., vol. 75–79, no. SUPPL., pp. 371–375, 2005.
C. Abeykoon, “Modelling of Heat Exchangers with Computational Fluid Dynamics,” Proc. 8th Int. Conf. Fluid Flow, Heat Mass Transf., no. May, 2021.
C. Abeykoon, “Compact heat exchangers – Design and optimization with CFD,” Int. J. Heat Mass Transf., vol. 146, p. 118766, 2020.
E. Pal, I. Kumar, J. B. Joshi, and N. K. Maheshwari, “CFD simulations of shell-side flow in a shell-and-tube type heat exchanger with and without baffles,” Chem. Eng. Sci., vol. 143, pp. 314–340, 2016.
Safiullah, K. Nishida, Y. Ogata, T. Oda, and K. Ohsawa, “Effects of nozzle hole size and rail pressure on diesel spray and mixture characteristics under similar injection rate profile – experimental, computational and analytical studies under non-evaporating spray condition,” Proc. Inst. Mech. Eng. Part D J. Automob. Eng., vol. 236, no. 2–3, pp. 310–321, 2022.
Safiullah, K. Nishida, and Y. Ogata, “Evaporation and mixture formation characteristics of diesel spray under various nozzle hole size and injection pressure condition employing similar injection rate profile,” Int. Commun. Heat Mass Transf., vol. 123, no. February, p. 105184, 2021.
C. Abeykoon, “Improving the Performance of Shell-and-Tube Heat Exchangers by the Addition of Swirl,” Int. J. Process Syst. Eng., vol. 2, no. 3, pp. 221–245, 2014.
C. Damis Widiawaty, R. Gunadi, and D. A. Syuriadi, “Pemodelan dan Analisis Kinerja dengan Metode CFD,” Politeknologi, vol. 16, no. 3, pp. 239–244, 2017.
A. Husen, T. M. I. Akbar, and N. Cholis, “Analisis pengaruh kecepatan aliran fluida dingin terhadap efektivitas shell and tube heat exchanger,” vol. 16, no. Vc, pp. 1–10, 2020.
R. Shanahan and A. Chalim, “STUDI LITERATUR TENTANG EFEKTIVITAS ALAT PENUKAR PANAS SHELL AND TUBE 1-1 SISTEM FLUIDA GLISERIN –,” vol. 6, no. 9, pp. 164–170, 2020.
DOI: https://doi.org/10.31284/j.jmesi.2023.v3i1.3544
Refbacks
- There are currently no refbacks.
This work is licensed under a Creative Commons Attribution-NonCommercial 4.0 International License.