Utilization of Hospital Solid Waste as Paving Blocks

Intan Dwi Wahyu Setyo Rini, Fadillah Afdalya Lukman, Adrian Gunawan

Abstract


A hospital as a health facility has the potential to produce medical waste, which is harmful to the environment, if it is not handled properly and correctly. At Hospital X, infectious medical waste is chopped and sterilized at temperatures above 100oC using a sterilwave to reduce the size of the waste and hand it over to a third party at a substantial cost. This waste has the potential to be used as construction materials, such as paving blocks, which are used as parks in the hospital area. Therefore, this research was conducted to determine the best paving block mix design and composition using chopped medical waste as a fine aggregate substitution. In addition, this research carried out a TCLP test on paving blocks that had the best water absorption to find out whether paving blocks are good enough to strip potential soil contamination. The quality target for paving blocks in this study was to meet class D quality with a minimum compressive strength of 8.5 MPa and a maximum water absorption of 10%. The quality of compressive strength and water absorption was based on SNI 03-0691-1996, and the TCLP test referred to Indonesia Government Regulation Number 22 of 2021. The results showed that the mix design used is 1:5 for the ratio of cement and fine aggregate with an average compressive strength of normal paving blocks of 10 MPa. Whereas paving blocks with a mixture of medical waste with the best absorption were those with as much as 8% substitution of fine aggregate, with an average compressive strength value of 10 MPa. The results of the TCLP test on the best specimens showed that the levels of heavy metals in medical waste paving blocks met the TCLP A quality standards and were safe for use in hospital parks.

Keywords


Hospital, Medical waste, Paving blocks, TCLP

Full Text:

PDF

References


R. U. , P. R. K. H. , dan A. S. Wulandari, “Evaluasi Kapasitas Pengolahan Air Limbah Rumah Sakit (Studi Pada Rumah Sakit X Surabaya),” Nusantara Hasana Journal, vol. 2, no. 8, pp. 205–211, 2023, Accessed: Apr. 05, 2023. [Online]. Available: http://nusantarahasanajournal.com/index.php/nhj/article/view/673/572

Khatami M.F., Mirwan M., and Aulidia S., “Evaluasi Sistem Pengelolaan Limbah Padat Bahan Berbahaya dan Beracun (B3) di Rumah Sakit X Surabaya,” Nusantara Hasana Journal, vol. 2, no. 8, pp. 182–191, 2023, Accessed: Apr. 05, 2023. [Online]. Available: http://nusantarahasanajournal.com/index.php/nhj/article/view/707/569

N. Nasrul, “Analisis Pengelolaan Limbah Medis Padat Di Rumah Sakit Umum Daerah Haji Abdoel Madjid Batoe (RSUD Hamba) Kabupaten Batanghari,” Mar. 2023.

Agus Susanto, Yusni Ikhwan Siregar, and Bayhakki, “Strategi Pengelolaan Limbah Bahan Berbahaya dan Beracun Fasilitas Pelayanan Kesehatan Rumah Sakit X Mandau,” SEHATI: Jurnal Kesehatan, vol. 3, no. 1, pp. 17–29, Feb. 2023, doi: 10.52364/sehati.v3i1.32.

I. D. W. S. Rini, M. Maria, E. M. Anifah, A. A. I. Saputra, A. Gunawan, and A. I. Arobi, “Analisis Dampak Lingkungan Pengolahan Limbah Fly Ash dan Bottom Ash dengan Metode Siklus Daur Hidup (Life Cycle Assessment/LCA) di Industri Pembangkit Listrik Tenaga Uap,” SPECTA Journal of Technology, vol. 6, no. 3, pp. 263–272, Jan. 2023, doi: 10.35718/specta.v6i3.761.

J. J. Ekaputri and M. S. Al Bari, “Perbandingan Regulasi Fly Ash sebagai Limbah B3 di Indonesia dan Beberapa Negara,” Media Komunikasi Teknik Sipil, vol. 26, no. 2, pp. 150–162, Dec. 2020, doi: 10.14710/MKTS.V26I2.30762.

Pemerintah Republik Indonesia, “Undang-undang Nomor 26 Tahun 2007,” 2007.

V. Ansari and E. Prianto, “Ciptakan Rumah Ramah Lingkungan Dengan Material Dinding Limbah Fly Ash Dan Bottom Ash (FABA),” Prosiding Seminar Sains Nasional dan Teknologi, vol. 1, no. 1, Nov. 2021, Accessed: Apr. 07, 2023. [Online]. Available: https://publikasiilmiah.unwahas.ac.id/index.php/PROSIDING_SNST_FT/article/view/4972

M. Jiang et al., “Different Material Footprint Trends between China and the World in 2007-2012 Explained by Construction- and Manufacturing-associated Investment,” One Earth, vol. 5, no. 1, pp. 109–119, Jan. 2022, doi: 10.1016/j.oneear.2021.12.011.

V. T. Dewi, M. L. Ashari, and D. Darmawan, “Analisis Pengaruh Limbah Slag dan Debu EAF (Electric Arc Furnace) Terhadap Uji SEM, Uji Kuat Tekan Beton, dan Uji TCLP,” Proceeding 1st Conference on Safety Engineering and Its Application, pp. 292–296, 2017.

I. Dwi et al., “Penggunaan Fly Ash Industri Pembangkit Listrik Tenaga Uap (PLTU) Sebagai Pengganti Semen Pada Beton,” Seminar Nasional Fakultas Teknik, 2019.

R. Fadhilatul and T. Sulistyaningsih, “Paving Block Berbahan Dasar Limbah Plastik Polyethylene dan Bottom Ash,” Seminar Nasional Teknologi Industri Hijau 2, vol. 2, no. 1, pp. 138–150, 2020.

A. Soehardjono, T. Hidayat, and G. S. Prawito, “Pengaruh Penggunaan Bottom Ash Sebagai Pengganti Semen Terhadap Nilai Kuat Tekan dan Kemampuan Resapan Air Struktur Paving,” Jurnal Rekayasa Sipil, vol. 7, no. 1, pp. 74–80, 2013.

W. W. Ningrum, A. Rakhmawati, and R. M. Jannah, “Pemanfaatan Limbah Plastik Low Density Polyethylene (LDPE) pada Paving Block Non Pasir,” ULIL ALBAB : Jurnal Ilmiah Multidisiplin, vol. 2, no. 2, pp. 617–624, Jan. 2023, doi: 10.56799/JIM.V2I2.1320.

M. R. Nurfaizi, A. Arifin, and G. C. Asbanu, “Pemanfaatan Limbah Plastik PET (Polyethylene Terephtalate), Limbah Pecahan Keramik dan Limbah Oli Bekas Menjadi Paving Block,” Jurnal Teknologi Lingkungan Lahan Basah, vol. 11, no. 1, pp. 034–040, Feb. 2023, doi: 10.26418/JTLLB.V11I1.57576.

E. Silfiani, D. W. Kurniawidi, T. Ardianto, and S. Rahayu, “Plastik LDPE (Low Density Polyethylene) Sebagai Campuran Komposit Polimer Paving Block,” ORBITA. Jurnal Hasil Kajian, Inovasi, dan Aplikasi Pendidikan Fisika, vol. 1, no. 1, pp. 1–7, 2023.

A. I. N. Diana and N. Zainah, “Pemanfaatan Limbah Abu Batok Kelapa dan Kapur Hidrolis Sebagai Bahan Substitusi Semen pada Paving Block,” Media Komunikasi Teknik Sipil, vol. 28, no. 2, pp. 276–283, 2022, Accessed: Apr. 08, 2023. [Online]. Available: https://ejournal.undip.ac.id/index.php/mkts/article/view/36136/23318

A. Intan, N. Diana, and N. Zainah, “Pemanfaatan Limbah Abu Batok Kelapa dan Kapur Hidrolis sebagai Bahan Substitusi Semen pada Paving Block,” MEDIA KOMUNIKASI TEKNIK SIPIL, vol. 28, no. 2, pp. 276–283, Jan. 2023, doi: 10.14710/MKTS.V28I2.36136.

A. Dumyati and D. F. Manalu, “Analisis Penggunaan Pasir Pantai Sampur Sebagai Agregat Halus Terhadap Kuat Tekan Beton,” Jurnal Fropil, vol. 3, no. 1, pp. 1–14, Jan. 2015.

Badan Standarisasi Nasional, SNI 03-0691-1996 Bata beton (Paving Block). Badan Standarisasi Nasional, 1996.

“Standar Nasional Indonesia Semen portland ICS 91.100.10 Badan Standardisasi Nasional.”

A. P. Putri, C. C. S. Khala, and G. R. Prayogi, “Comparative Study Of Changes in SNI 1727 (2013-2020) and SNI 1726 (2012-2019),” Journal of Advanced Civil and Environmental Engineering, vol. 5, no. 2, p. 74, Nov. 2022, doi: 10.30659/jacee.5.2.74-83.

H. Nofrianto and Hutrio, “Analisis Mutu Paving Block Dengan Variasi Agregat Halus,” Jurnal Teknologi dan Vokasi, vol. 1, no. 1, pp. 54–62, Jan. 2023.

Badan Standardisasi Nasional, SNI 03-6825-2002 Metode Pengujian Kekuatan Tekan Mortar Semen Portland Untuk Pekerjaan Sipil. Badan Standarisasi Nasional , 2002.

C. Aditya, “Pengaruh Penggunaan Limbah Pasir Onyx Sebagai Substitusi Pasir Terhadap Kuat Tekan, Penyerapan Air, dan Ketahanan Aus Paving Block,” Widya Teknika, vol. 20, no. 1, Mar. 2012, Accessed: Apr. 12, 2023. [Online]. Available: http://publishing-widyagama.ac.id/ejournal-v2/index.php/widyateknika/article/view/3

Pemerintah Republik Indonesia, “Peraturan Pemerintah Nomor 22 Tahun 2021,” Jakarta, 2021.

R. Anisa, “Studi Pemanfaatan Limbah Abu Incinerator RSUD Dr Kanujoso Djatiwibowo Balikpapan menjadi Paving Block,” Balikpapan, 2022.

Zianuri, “Penanganan Sampah Plastik pada Produksi Paving Block,” Jurnal Teknologi Lingkungan, vol. 22, no. 2, pp. 170–177, 2021.

T. B. Aulia and Rinaldi, “Bending capacity analysis of high-strength reinforced concrete beams using environmentally friendly synthetic fiber composites,” in Procedia Engineering, Elsevier Ltd, 2015, pp. 1121–1128. doi: 10.1016/j.proeng.2015.11.136.

F. Syefringga, “Pengaruh Penambahan Limbah Plastik Sebagai Campuran Beton Terhadap Kuat Tekan dan Daya Serap Air Pada Paving Block,” Pekanbaru, 2021.

D. Larasati and I. Setyanto, “Uji Kuat Tekan Paving Block Menggunakan Campuran Tanah dan kapur dengan Alat Pemadat Modifikasi,” JRSDD, vol. 4, no. 1, pp. 11–22, 2016.

Rezasyah Alifiadi and Agus Slamet, “Utilization of Sandblasting Waste as an Alternative Material for Paving Blocks,” Jurnal Multidisiplin Madani, vol. 2, no. 12, pp. 4399–4407, Dec. 2022, doi: 10.55927/mudima.v2i12.1911.

A. A. Werkneh, G. G. Gebretsadik, and S. B. Gebru, “Review on Environmental Selenium: Occurrence, Public Health Implications and Biological Treatment Strategies,” Environmental Challenges, vol. 11, Apr. 2023, doi: 10.1016/j.envc.2023.100698.

R. D. Singh, S. K. Jurel, S. Tripathi, K. K. Agrawal, and R. Kumari, “Mercury and other biomedical waste management practices among dental practitioners in India,” Biomed Res Int, vol. 2014, 2014, doi: 10.1155/2014/272750.

Pemerintah Republik Indonesia, Peraturan Menteri Lingkungan Hidup dan Kehutanan Nomor 56 Tahun 2015. 2015, pp. 1–114. [Online]. Available: www.peraturan.go.id




DOI: https://doi.org/10.31284/j.iptek.2024.v28i2.5964

Refbacks

  • There are currently no refbacks.